| ANALOG AUDIO SECTION |
| Input Impedance |
20 kΩ
|
Output Impedance
|
|
Main–RCA
Main–XLR
Zones 2/3 and Record |
|
|
| Rated Input |
2.0 Vrms
|
| Maximum Input |
5.3 Vrms
|
| Rated Output (100 kΩ load) |
2.0 Vrms
|
| Minimum Load |
5 kΩ
|
|
|
|
| Headphone Output |
100 mW into 32 Ω at 0.2% THD+N
|
| Volume Control Range |
|
Main
Zone 2/3 and Headphone |
|
|
|
-95.5 dB to +31.5 dB (in 0.5 dB increments)
-62.5 dB to +10.0 dB (in 1.25 dB increments)
|
|
| Channel Separation (at 1 kHz) |
82 dB
|
| Crosstalk Between Inputs (at 1 kHz) |
86 dB
|
| XLR Pin Configuration |
Pin 1: Ground, Pin 2: Positive, Pin 3: Negative
|
| DIGITAL AUDIO SECTION |
| All digital audio inputs and outputs are to S/PDIF electrical (75 Ω, 0.5 Vp-p), S/PDIF optical (Toslink), or AES/EBU (110 Ω, 5 Vp-p) standards. SRC output is 24-bit/192 kHz regardless of input. |
Analog to Digital Converters
|
AKM® AK5394A
|
| Input Receiver |
AKM® AK4112A
|
| Processor |
Dual Motorola® 56367 at 150 MHz
|
| Sample Rate Converters |
Analog Devices AD1896
|
| Digital to Analog Converters |
AKM® AK4395
|
| SIGNAL PROCESSING |
| Crossover |
|
High-Pass Slope (Small Speaker Setting)
Low-Pass Slope (Subwoofer)
Frequency (Adjustable in 5-Hz increments) |
|
|
|
12 dB/octave (2nd order)
24 dB/octave (4th order)
25 Hz to 160 Hz
|
|
| Tone Control |
|
Filter Response Type
Bass Turnover Frequency
Treble Turnover Frequency
Range
|
|
|
|
Shelf
200 Hz
2 kHz
±12 dB
|
|
| MAIN PATH |
| (RCA and XLR Output, 48 kHz Sampling Rate for all Digital Signal Paths) |
| Frequency Response and Bandwidth |
|
Analog-Direct Inputs
|
|
Analog-DSP Inputs at 24/96
|
|
Digital Inputs at 24/96
|
|
|
|
10 Hz to 20 kHz
(+0 -0.2 dB), 1 Hz to 130 kHz (-3 dB)
|
|
24/96 10 Hz to 20 kHz (+0 -0.3 dB), 2 Hz to 44 kHz (-3 dB)
|
|
24/96 10 Hz to 20 kHz
(+0 -0.2 dB), 1 Hz to 45 kHz (-3 dB)
|
|
| THD+N (at Rated Input and Output) |
|
Analog-Direct Inputs |
|
Analog-DSP Inputs at 24/48 or 24/96 |
|
Digital Inputs at 24/48 or 24/96 |
|
|
|
0.006% (80 kHz BW)
|
|
0.004% (AES17 filter)
|
|
0.004% (AES17 filter)
|
|
| IMD (CCIF at 15 kHz and 16 kHz) |
|
6-Ch S/E Direct Input |
|
2-Ch BAL Direct Input |
|
2-Ch S/E Direct Input |
|
Analog-DSP Inputs at 24/48 |
|
Digital Inputs at 24/48 or 24/96 |
|
|
|
<0.001%
|
|
<0.001%
|
|
<0.001%
|
|
0.001%
|
|
0.001%
|
|
| S/N Ratio (ref. 2.0 Vrms; IEC-A Filter) |
|
Analog-Direct Inputs |
|
Analog-DSP Inputs at 24/48 or 24/96 |
|
Digital Inputs at 24/48 or 24/96 |
|
|
| ZONE 2 and ZONE 3 PATHS |
Frequency Response and Bandwidth
|
20 Hz to 20 kHz (+0, -0.1 dB),
3 Hz to 140 kHz (+0, -3 dB)
|
| THD+N (at Rated Input and Output) |
0.06% (80 kHz BW)
|
| IMD (CCIF at 15 kHz and 16 kHz) |
0.06%
|
| S/N Ratio (ref. 2.0 Vrms, IEC-A Filter) |
97 dB
|
| RECORD PATH |
| Analog to Digital Conversion S/N Ratio (A-weighted) |
103 dB
|
| FM TUNER |
| Sensitivity |
|
50 dB S/N
IHF |
|
|
|
13 dBµ typical, 25 dBµ max.
10 dBµ typical, 20 dBµ max.
|
|
|
|
|
|
75 dB typical, 65 dB min.
69 dB typical, 60 dB min.
|
|
|
|
|
|
0.2% typical, 1.0% max.
0.3% typical, 1.5% max.
|
|
| Stereo Separation |
40 dB typical, 25 dB min.
|
| Adjacent Channel Selectivity (±400 kHz) |
70 dB typical, 60 dB min.
|
| Frequency Response |
25 Hz to 15 kHz (±1 dB)
|
| AM TUNER |
| Sensitivity (20 dB S/N) |
49 dBµ typical, 56 dBµ max.
|
| S/N Ratio |
50 dB typical, 43 dB min.
|
| Distortion |
0.7% typical, 2.0% max.
|
| One-Signal Selectivity (±10 kHz) |
24 dB typical, 18 dB min.
|
| VIDEO |
| Bandwidth of complete path from input to output |
|
Composite and S-Video
Component:
Y
Pr/Cr
Pb/Cb |
|
|
70 MHz
110 MHz
90 MHz
80 MHz
|
|
| All video inputs and outputs are 75 Ω, 1.5 Vp-p. Component video switching is suitable for any format up to 1080p (line-doubled 1080i). |
| CONTROL |
| Infrared |
|
Carrier Frequency
Max. 12V Supply Current
Maximum Emitter Current |
|
|
|
38 kHz
150 mA
100 mA per output
|
|
| RS-232 Interface |
|
Connection
Pinout (Statement D1 side)
Baud Rate
Configuration |
|
|
|
DB-9F, straight-wired
Pin 2:Tx, Pin 3:Rx, Pin 5: Ground
1200 to 115200
8 data bits, 1 stop bit, no parity bits,
flow control (RTS, CTS, NONE)
|
|
| Trigger Outputs |
|
Polarity
Maximum Current at 12 VDC
Sequential Delay |
|
|
|
3.5 mm mono (tip positive), sleeve negative
50 mA (Triggers 1,2), 200 mA (Trigger 3)
250 ms
|
|
| POWER REQUIREMENTS |
| Supply Voltage |
105 to 130 V, 60 Hz
|
| Power Consumption |
Maximum 140 W
|
| Fuse Ratings (Fuses are internal) |
|
Main Power Supply
Standby Power Supply |
|
|
|
1.5 A slow-blow 5 x 20 mm
0.5 A slow-blow 5 x 20 mm
|
|
| DIMENSIONS |
| Height |
5-7/8 inches (14.9 cm) including feet; Rack-mounting: 3 rack units, without feet
|
| Width |
Faceplate 19-1/4 inches (49 cm)
Chassis 17-1/4 inches (43.8 cm)
|
| Depth |
15-1/4 inches (38.7 cm)
|
| Weight (unpacked) |
24.3 lb (11 kg)
|
|
|
